SET

Set your friendly name. Others can request this name with the NAME command. There are following meta characters you can use:

$S: Hardware serial number, all ten digits

$s: Hardware serial number, last three digits

$P: Server port

$p: Server port, last digit

$H: FQDN

$h: hostname

$$: $

The default value is $S_$p.

If enabled, some SDP result codes will have literal values instead of numeric values.

0: No (always use numeric values)

1: Yes (literal values)

Set master/slave role switch preference, optionally also link policy and link supervision timeout. Possible values for "role" are:

0: allow calling, don't request when answering

1: allow calling, request when answering

2: don't allow calling, request when answering

The default link policy is 000f and the default link supervision timeout is 7d00. See Bluetooth Specification for more information on these.

Whether or not to use Bluetooth encryption. To actually have Bluetooth encryption enabled, the connection has to be authenticated.

0: No

1: Yes

Pagemode controls whether or not other devices can find and call you. There are four different modes:

0: No inquiry, no paging

1: Inquiry, no paging

2: No inquiry, paging

3: Inquiry and paging

Page timeout is in hex and the default value is 2000. Default page repetition mode is 2 (R2). Default scan activity is interval 0800 and window 0012 (R1). Default inquiry activity is interval 0800 and window 0012 (R1).

See Bluetooth Specification for more information on these.

Automatically hide baseband (set pagemode to 0) if there are more than physical ACL links or logical connections. Value 0 means "don't care".

Default values: 7 0

Set PIN code for bdaddr.

Authflags are:

--NEWPAIR Only if we do not have linkkey yet

--REQUEST Request this pin from remote, do not reply with this one

--REPLY Reply with this pin to remote requests

--CALL Only if making outgoing call

--ANSWER Only when answering to incoming call

--RFCOMM Call type is RFCOMM (includes FORK/PPP/...)

--BNEP Call type is BNEP

--L2CAP Call type is L2CAP

Default authflags are all but --NEWPAIR enabled.

There are three special pins:

- Reject without asking pin.

-- Reject on the connection open, do not check for call types.

+ Accept without asking pin.

Manually set linkkey for bdaddr.

Note: SET BLUETOOTH AUTH must also be set for some value to enable encrypted connections with previously stored link keys.

Add fork-listener for the channel. When there is an incoming RFCOMM connection to the channel iWRAP server will handle the connection by itself by forking "cmd". At least "mem" kilobytes of free memory must be available, or the connection will be rejected. After forking iWRAP server will wait "delay" timerticks (50ms) before transmitting any data.

The client application should modify both the stdout and stdin pipes and set NOECHO, 8BIT and all other necessary modes in the very beginning. The purpose of the "delay" parameter is to give the application enough time to do this.

Modify slaves powermode according to "mode". "params" are optional and mode-dependent. Possible values for "mode" are 0, 1, 2, 3, 4:

0: Active.

Params: None.

1: Park: Round-robin.

Params: max_beacon min_beacon sleep_after_unpark sleep_after_round

Defaults: 254 160 5 30

Sleeps are specified by timerticks (50ms).

2: Park: Idle.

Params: max_beacon min_beacon max_active

Defaults: 512 384 6

max_active is the maximum number of active slaves.

3: Sniff: All.

Params: max_interval min_interval attempt timeout

Defaults: 640 426 1 8

4: Sniff: Idle.

Params: idle_timeout max_interval min_interval attempt timeout

Defaults: 400 640 426 1 32

idle_timeout is in timerticks (50ms).

See Bluetooth Specification for more information on params.

Set default QoS values for new connection. Parameters are in hex. See Bluetooth Specification for more information on params.

Defaults: 01 00000000 00000000 000061a8 ffffffff

Define FlushTimeout and LinkTimeout for L2CAP connections. See Bluetooth Specification for more information on params.

Defaults: 65535 40000

This setting controls whether or not the iWRAP server should modify the defaultroute setting. There are four different modes:

0: Don't alter defaultroute

1: Set defaultroute according to outgoing PPP

2: Set defaultroute according to incoming PPP

3: Set defaultroute according to all PPP calls

Controls incoming PAN connections. Bitmap:

1: Allow incoming PAN-PANU connection.

2: Allow incoming PAN-GN connection.

4: Allow incoming PAN-NAP connection.

8: Enable zeroconf for incoming PAN-PANU connections.

16: Enable zeroconf for outgoing PAN-PANU connections.

For most cases value "6" (the default) is recommended.

Enable password. iWRAP clients must send this password before giving any other command. The password is case sensitive.

With optional --LOCAL parameter clients coming from localhost are accepted without password.

Set powermode for link_id park. Required "params" are:

avg_beacon or

max_beacon min_beacon

See Bluetooth Specification for more information on params.

Set link's powermode to hold. Required "params" are:

avg

max min

See Bluetooth Specification for more information on params.

Set powermode for link_id to sniff. Required "params" are:

avg_interval or

max_interval min_interval or

max_interval min_interval attempt or

max_interval min_interval attempt timeout

Default attempt is 1, default timeout is 8.

See Bluetooth Specification for more information on params.

Set link's QoS values. Parameters are in hex.

See Bluetooth Specification for more information on params.